Motherboard Forums


Reply
Thread Tools Display Modes

Hard drive partitions not recognised in computer

 
 
JD Francis
Guest
Posts: n/a
 
      11-03-2008, 08:38 AM
I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
Deskstar T7K250. When this hard drive is in the computer and I try to
run the Windows XP Professional setup CD, it does not recognise any of
the partitions and is unable to modify the disk in any way. When I
connect the drive to another computer via a USB cable and run the
setup, it can detect all the drive partitions and modify them.

Is there a way to get this hard drive working for Windows in my
computer?
 
Reply With Quote
 
 
 
 
Ben Myers
Guest
Posts: n/a
 
      11-03-2008, 01:19 PM
JD Francis wrote:
> I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> Deskstar T7K250. When this hard drive is in the computer and I try to
> run the Windows XP Professional setup CD, it does not recognise any of
> the partitions and is unable to modify the disk in any way. When I
> connect the drive to another computer via a USB cable and run the
> setup, it can detect all the drive partitions and modify them.
>
> Is there a way to get this hard drive working for Windows in my
> computer?


You purchased a used drive if it already had partitions on it. Wipe the
hard drive clean with CopyWipe (free), and try again. The existing
partitions are causing some confusion... Ben Myers
 
Reply With Quote
 
 
 
 
JD Francis
Guest
Posts: n/a
 
      11-09-2008, 09:48 PM
On Nov 3, 1:19*pm, Ben Myers <(E-Mail Removed)> wrote:
> JD Francis wrote:
> > I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> > Deskstar T7K250. *When this hard drive is in the computer and I try to
> > run the Windows XP Professional setup CD, it does not recognise any of
> > the partitions and is unable to modify the disk in any way. *When I
> > connect the drive to another computer via a USB cable and run the
> > setup, it can detect all the drive partitions and modify them.

>
> > Is there a way to get this hard drive working for Windows in my
> > computer?

>
> You purchased a used drive if it already had partitions on it. *Wipe the
> hard drive clean with CopyWipe (free), and try again. *The existing
> partitions are causing some confusion... Ben Myers


I already completely wiped it with the manufacturer's disk utility
program, but this made no difference to the Windows XP Professional
CD. I should probably add, that using a Windows XP Home CD, I am able
to install the operating system on the NTFS partition, which it
recognises, with no problems.
 
Reply With Quote
 
- Bobb -
Guest
Posts: n/a
 
      11-13-2008, 07:15 PM

"JD Francis" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
On Nov 3, 1:19 pm, Ben Myers <(E-Mail Removed)> wrote:
> JD Francis wrote:
> > I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> > Deskstar T7K250. When this hard drive is in the computer and I try to
> > run the Windows XP Professional setup CD, it does not recognise any of
> > the partitions and is unable to modify the disk in any way. When I
> > connect the drive to another computer via a USB cable and run the
> > setup, it can detect all the drive partitions and modify them.

>
> > Is there a way to get this hard drive working for Windows in my
> > computer?

>
> You purchased a used drive if it already had partitions on it. Wipe the
> hard drive clean with CopyWipe (free), and try again. The existing
> partitions are causing some confusion... Ben Myers


I already completely wiped it with the manufacturer's disk utility
program, but this made no difference to the Windows XP Professional
CD. I should probably add, that using a Windows XP Home CD, I am able
to install the operating system on the NTFS partition, which it
recognises, with no problems.

So it was a used drive?
Came from Windows environment ? ( vs. Unix,VMS, etc)
What do you mean by "completely wiped it" ?
Reformatted ?
If works as secondary drive, there the primary boot area is not used.
Did you look at disk structure when installing XP Home ?
Were there more than one partition ?
Were you able to delete existing partitions ?
Might it be you installed XP home to second partition?
So are you now all set, or still trying to install XP Pro
Can you install XP Pro NOW ( with XP home on there)

 
Reply With Quote
 
JD Francis
Guest
Posts: n/a
 
      11-15-2008, 04:26 AM
On Nov 13, 7:15*pm, "- Bobb -" <b...@noemail.123> wrote:
> "JD Francis" <(E-Mail Removed)> wrote in message
>
> news:(E-Mail Removed)...
> On Nov 3, 1:19 pm, Ben Myers <(E-Mail Removed)> wrote:
>
> > JD Francis wrote:
> > > I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> > > Deskstar T7K250. When this hard drive is in the computer and I try to
> > > run the Windows XP Professional setup CD, it does not recognise any of
> > > the partitions and is unable to modify the disk in any way. When I
> > > connect the drive to another computer via a USB cable and run the
> > > setup, it can detect all the drive partitions and modify them.

>
> > > Is there a way to get this hard drive working for Windows in my
> > > computer?

>
> > You purchased a used drive if it already had partitions on it. Wipe the
> > hard drive clean with CopyWipe (free), and try again. The existing
> > partitions are causing some confusion... Ben Myers

>
> I already completely wiped it with the manufacturer's disk utility
> program, but this made no difference to the Windows XP Professional
> CD. *I should probably add, that using a Windows XP Home CD, I am able
> to install the operating system on the NTFS partition, which it
> recognises, with no problems.
>
> So it was a used drive?
> Came from Windows environment ? ( vs. Unix,VMS, etc)
> What do you mean by "completely wiped it" ?
> Reformatted ?
> If works as secondary drive, there the primary boot area is not used.
> Did you look at disk structure when installing XP Home ?
> Were there more than one partition ?
> Were you able to delete existing partitions ?
> Might it be you installed XP home to second partition?
> So are you now all set, or still trying to install XP Pro
> Can you install XP Pro NOW *( with XP home on there)


The drive was used, yes. I don't know its history, but it did have a
single NTFS partition on it when I got it that got deleted when I zero-
filled the disk. Windows XP Home setup can see NTFS partitions and
indicates that they are of this format, but the Windows XP
Professional setup simply says "Unknown" and displays the error "Setup
was unable to format the partition. The disk may be damaged" message
when I try to manipulate the drive in any way.

I've already tried installing XP Professional from a Home
installation. Everything works fine up until the point where it
reboots, where I get a Stop 0x00000024 error.

The drive is fine; I've already run a scan on it. I believe the error
is to do with either the configuration of the drive or that of the
computer, rather than a fault with the drive. Also, on another thread
I started in another group, somebody asked whether the XP Professional
disk had a SP other than 1 on it while the XP Home disk had SP1 on
it. This is correct, so I am wondering whether this difference in
service packs bears any significance on the issue I am having.
However, I have no way of obtaining an XP Professional SP1 disk so I
am kinda screwed there if that is the cause of the problem.
 
Reply With Quote
 
- Bobb -
Guest
Posts: n/a
 
      11-15-2008, 06:03 PM

"JD Francis" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
On Nov 13, 7:15 pm, "- Bobb -" <b...@noemail.123> wrote:
> "JD Francis" <(E-Mail Removed)> wrote in message
>
> news:(E-Mail Removed)...
> On Nov 3, 1:19 pm, Ben Myers <(E-Mail Removed)> wrote:
>
> > JD Francis wrote:
> > > I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> > > Deskstar T7K250. When this hard drive is in the computer and I try to
> > > run the Windows XP Professional setup CD, it does not recognise any of
> > > the partitions and is unable to modify the disk in any way. When I
> > > connect the drive to another computer via a USB cable and run the
> > > setup, it can detect all the drive partitions and modify them.

>
> > > Is there a way to get this hard drive working for Windows in my
> > > computer?

>
> > You purchased a used drive if it already had partitions on it. Wipe the
> > hard drive clean with CopyWipe (free), and try again. The existing
> > partitions are causing some confusion... Ben Myers

>
> I already completely wiped it with the manufacturer's disk utility
> program, but this made no difference to the Windows XP Professional
> CD. I should probably add, that using a Windows XP Home CD, I am able
> to install the operating system on the NTFS partition, which it
> recognises, with no problems.
>
> So it was a used drive?
> Came from Windows environment ? ( vs. Unix,VMS, etc)
> What do you mean by "completely wiped it" ?
> Reformatted ?
> If works as secondary drive, there the primary boot area is not used.
> Did you look at disk structure when installing XP Home ?
> Were there more than one partition ?
> Were you able to delete existing partitions ?
> Might it be you installed XP home to second partition?
> So are you now all set, or still trying to install XP Pro
> Can you install XP Pro NOW ( with XP home on there)


The drive was used, yes. I don't know its history, but it did have a
single NTFS partition on it when I got it that got deleted when I zero-
filled the disk. Windows XP Home setup can see NTFS partitions and
indicates that they are of this format, but the Windows XP
Professional setup simply says "Unknown" and displays the error "Setup
was unable to format the partition. The disk may be damaged" message
when I try to manipulate the drive in any way.

I've already tried installing XP Professional from a Home
installation. Everything works fine up until the point where it
reboots, where I get a Stop 0x00000024 error.

The drive is fine; I've already run a scan on it. I believe the error
is to do with either the configuration of the drive or that of the
computer, rather than a fault with the drive. Also, on another thread
I started in another group, somebody asked whether the XP Professional
disk had a SP other than 1 on it while the XP Home disk had SP1 on
it. This is correct, so I am wondering whether this difference in
service packs bears any significance on the issue I am having.
However, I have no way of obtaining an XP Professional SP1 disk so I
am kinda screwed there if that is the cause of the problem.
========
Stop 24 error:
" an unrecoverable error when trying to access an NTFS partition or a volume
on the hard disk. Typically, you receive a "Stop: 0x00000024" error message
when the file system or partition structure is corrupted "

I've installed XP Pro w/SP2 from scratch, and it installed fine so I don't
think it's your software CD. Still sounds like physical disk issue to me. I
suspect drive was previously in non-NTFS environment and the boot area is
not recognized by install program. Why an issue in Pro and not Home ?
Perhaps utilities dated differently ?? whatever the reason:
Are you familiar with FDISK ?
" The fdisk command in Windows 95 and Windows 98 lets you delete NTFS
partitions by selecting and deleting the NON-DOS partition. "

Can you make a Win98 boot disk ? or Norton Ghost ? Ultimate Boot CD etc
to be able to :
1. boot a floppy ( or CD). Then, in DOS (either PC DOS or MS-DOS)
2. low level format the drive
3. partition the drive
4. format the drive ( FAT32)
5. run chkdsk /f just to check drive
6 if you are familiar with SYS command,
type sys C:
to initialize the boot block ( to boot up Win98 )
( http://www.computerhope.com/syshlp.htm )

Doing those steps will erase everything on the drive , then make sure that
the boot block is writeable- and chkdsk should finish with no errors. Check
the output for bad blocks etc.
That should get you to a blank disk that has one and only one partition and
a good boot block.

Now that the drive has been initialized, boot the XP Pro CD ( make CD first
in flow, otherwise will get Win98 C:\ prompt)

5. Install XP Pro . When it asks for disk structure , first 'View existing
partitions", just to be sure nothing there - no hardware error, then "
Delete all "partitions. Then "Create" using all of the disk.
That should do it.

http://support.microsoft.com/kb/228888/en-us
for the STOP error ( I know it says Windows 2000 , but just go with it)
or
http://support.microsoft.com/kb/935806
( halfway down)
Search results for your problem:
http://search.microsoft.com/Results....FORM=QBME1&l=1


 
Reply With Quote
 
JD Francis
Guest
Posts: n/a
 
      11-19-2008, 07:51 PM
On Nov 15, 6:03*pm, "- Bobb -" <b...@noemail.123> wrote:
> "JD Francis" <(E-Mail Removed)> wrote in message
>
> news:(E-Mail Removed)...
> On Nov 13, 7:15 pm, "- Bobb -" <b...@noemail.123> wrote:
>
>
>
> > "JD Francis" <(E-Mail Removed)> wrote in message

>
> >news:(E-Mail Removed)....
> > On Nov 3, 1:19 pm, Ben Myers <(E-Mail Removed)> wrote:

>
> > > JD Francis wrote:
> > > > I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> > > > Deskstar T7K250. When this hard drive is in the computer and I try to
> > > > run the Windows XP Professional setup CD, it does not recognise anyof
> > > > the partitions and is unable to modify the disk in any way. When I
> > > > connect the drive to another computer via a USB cable and run the
> > > > setup, it can detect all the drive partitions and modify them.

>
> > > > Is there a way to get this hard drive working for Windows in my
> > > > computer?

>
> > > You purchased a used drive if it already had partitions on it. Wipe the
> > > hard drive clean with CopyWipe (free), and try again. The existing
> > > partitions are causing some confusion... Ben Myers

>
> > I already completely wiped it with the manufacturer's disk utility
> > program, but this made no difference to the Windows XP Professional
> > CD. I should probably add, that using a Windows XP Home CD, I am able
> > to install the operating system on the NTFS partition, which it
> > recognises, with no problems.

>
> > So it was a used drive?
> > Came from Windows environment ? ( vs. Unix,VMS, etc)
> > What do you mean by "completely wiped it" ?
> > Reformatted ?
> > If works as secondary drive, there the primary boot area is not used.
> > Did you look at disk structure when installing XP Home ?
> > Were there more than one partition ?
> > Were you able to delete existing partitions ?
> > Might it be you installed XP home to second partition?
> > So are you now all set, or still trying to install XP Pro
> > Can you install XP Pro NOW ( with XP home on there)

>
> The drive was used, yes. *I don't know its history, but it did have a
> single NTFS partition on it when I got it that got deleted when I zero-
> filled the disk. *Windows XP Home setup can see NTFS partitions and
> indicates that they are of this format, but the Windows XP
> Professional setup simply says "Unknown" and displays the error "Setup
> was unable to format the partition. *The disk may be damaged" message
> when I try to manipulate the drive in any way.
>
> I've already tried installing XP Professional from a Home
> installation. *Everything works fine up until the point where it
> reboots, where I get a Stop 0x00000024 error.
>
> The drive is fine; I've already run a scan on it. *I believe the error
> is to do with either the configuration of the drive or that of the
> computer, rather than a fault with the drive. *Also, on another thread
> I started in another group, somebody asked whether the XP Professional
> disk had a SP other than 1 on it while the XP Home disk had SP1 on
> it. *This is correct, so I am wondering whether this difference in
> service packs bears any significance on the issue I am having.
> However, I have no way of obtaining an XP Professional SP1 disk so I
> am kinda screwed there if that is the cause of the problem.
> ========
> Stop 24 error:
> " an unrecoverable error when trying to access an NTFS partition or a volume
> on the hard disk. Typically, you receive a "Stop: 0x00000024" error message
> when *the file system or partition structure is corrupted "
>
> I've installed XP Pro w/SP2 from scratch, and it installed fine so I don't
> think it's your software CD. Still sounds like physical disk issue to me.I
> suspect drive was previously in non-NTFS environment and the boot area is
> not recognized by install program. Why an issue in Pro and not Home ?
> Perhaps utilities dated differently ?? whatever the reason:
> Are you familiar with FDISK ?
> " The fdisk command in Windows 95 and Windows 98 lets you delete NTFS
> partitions by selecting and deleting the NON-DOS partition. "
>
> Can you make a Win98 boot disk ? *or Norton Ghost ? *Ultimate Boot CDetc
> to be able to :
> 1. boot a floppy ( or CD). Then, in DOS (either PC DOS or MS-DOS)
> 2. low level format the drive
> 3. partition the drive
> 4. format the drive ( FAT32)
> 5. run chkdsk /f just to check drive
> 6 *if you are familiar with SYS command,
> * *type * sys C:
> to initialize the boot block ( to boot up Win98 )
> (http://www.computerhope.com/syshlp.htm*)
>
> Doing those steps will erase everything on the drive , then make sure that
> the boot block is writeable- *and chkdsk should finish with no errors. Check
> the output for bad blocks etc.
> That should get you to a blank disk that has one and only one partition and
> a good boot block.
>
> Now that the drive has been initialized, boot the XP Pro CD ( make CD first
> in flow, otherwise will get Win98 C:\ prompt)
>
> 5. Install XP Pro . When it asks for disk structure , first 'View existing
> partitions", just to be sure nothing there *- *no hardware error, then *"
> Delete all "partitions. Then "Create" using all of the disk.
> That should do it.
>
> http://support.microsoft.com/kb/228888/en-us
> for the STOP error * *( I know it says Windows 2000 , but just go with it)
> orhttp://support.microsoft.com/kb/935806
> ( halfway down)
> Search results for your problem:http://search.microsoft.com/Results....ll+XP+Stop+0x0...


I'm not doing all of that. I know what the stop error is for, but
clearly there's nothing wrong with my drive if I can install Windows
XP Home on it. However, I have noticed that installing a Service Pack
over it causes it to not boot. Is there a way to troubleshoot this
and then work from there?
 
Reply With Quote
 
- Bobb -
Guest
Posts: n/a
 
      11-19-2008, 08:32 PM

"JD Francis" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
On Nov 15, 6:03 pm, "- Bobb -" <b...@noemail.123> wrote:
> "JD Francis" <(E-Mail Removed)> wrote in message
>
> news:(E-Mail Removed)...
> On Nov 13, 7:15 pm, "- Bobb -" <b...@noemail.123> wrote:
>
>
>
> > "JD Francis" <(E-Mail Removed)> wrote in message

>
> >news:(E-Mail Removed)...
> > On Nov 3, 1:19 pm, Ben Myers <(E-Mail Removed)> wrote:

>
> > > JD Francis wrote:
> > > > I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> > > > Deskstar T7K250. When this hard drive is in the computer and I try
> > > > to
> > > > run the Windows XP Professional setup CD, it does not recognise any
> > > > of
> > > > the partitions and is unable to modify the disk in any way. When I
> > > > connect the drive to another computer via a USB cable and run the
> > > > setup, it can detect all the drive partitions and modify them.

>
> > > > Is there a way to get this hard drive working for Windows in my
> > > > computer?

>
> > > You purchased a used drive if it already had partitions on it. Wipe
> > > the
> > > hard drive clean with CopyWipe (free), and try again. The existing
> > > partitions are causing some confusion... Ben Myers

>
> > I already completely wiped it with the manufacturer's disk utility
> > program, but this made no difference to the Windows XP Professional
> > CD. I should probably add, that using a Windows XP Home CD, I am able
> > to install the operating system on the NTFS partition, which it
> > recognises, with no problems.

>
> > So it was a used drive?
> > Came from Windows environment ? ( vs. Unix,VMS, etc)
> > What do you mean by "completely wiped it" ?
> > Reformatted ?
> > If works as secondary drive, there the primary boot area is not used.
> > Did you look at disk structure when installing XP Home ?
> > Were there more than one partition ?
> > Were you able to delete existing partitions ?
> > Might it be you installed XP home to second partition?
> > So are you now all set, or still trying to install XP Pro
> > Can you install XP Pro NOW ( with XP home on there)

>
> The drive was used, yes. I don't know its history, but it did have a
> single NTFS partition on it when I got it that got deleted when I zero-
> filled the disk. Windows XP Home setup can see NTFS partitions and
> indicates that they are of this format, but the Windows XP
> Professional setup simply says "Unknown" and displays the error "Setup
> was unable to format the partition. The disk may be damaged" message
> when I try to manipulate the drive in any way.
>
> I've already tried installing XP Professional from a Home
> installation. Everything works fine up until the point where it
> reboots, where I get a Stop 0x00000024 error.
>
> The drive is fine; I've already run a scan on it. I believe the error
> is to do with either the configuration of the drive or that of the
> computer, rather than a fault with the drive. Also, on another thread
> I started in another group, somebody asked whether the XP Professional
> disk had a SP other than 1 on it while the XP Home disk had SP1 on
> it. This is correct, so I am wondering whether this difference in
> service packs bears any significance on the issue I am having.
> However, I have no way of obtaining an XP Professional SP1 disk so I
> am kinda screwed there if that is the cause of the problem.
> ========
> Stop 24 error:
> " an unrecoverable error when trying to access an NTFS partition or a
> volume
> on the hard disk. Typically, you receive a "Stop: 0x00000024" error
> message
> when the file system or partition structure is corrupted "
>
> I've installed XP Pro w/SP2 from scratch, and it installed fine so I don't
> think it's your software CD. Still sounds like physical disk issue to me.
> I
> suspect drive was previously in non-NTFS environment and the boot area is
> not recognized by install program. Why an issue in Pro and not Home ?
> Perhaps utilities dated differently ?? whatever the reason:
> Are you familiar with FDISK ?
> " The fdisk command in Windows 95 and Windows 98 lets you delete NTFS
> partitions by selecting and deleting the NON-DOS partition. "
>
> Can you make a Win98 boot disk ? or Norton Ghost ? Ultimate Boot CD etc
> to be able to :
> 1. boot a floppy ( or CD). Then, in DOS (either PC DOS or MS-DOS)
> 2. low level format the drive
> 3. partition the drive
> 4. format the drive ( FAT32)
> 5. run chkdsk /f just to check drive
> 6 if you are familiar with SYS command,
> type sys C:
> to initialize the boot block ( to boot up Win98 )
> (http://www.computerhope.com/syshlp.htm )
>
> Doing those steps will erase everything on the drive , then make sure that
> the boot block is writeable- and chkdsk should finish with no errors.
> Check
> the output for bad blocks etc.
> That should get you to a blank disk that has one and only one partition
> and
> a good boot block.
>
> Now that the drive has been initialized, boot the XP Pro CD ( make CD
> first
> in flow, otherwise will get Win98 C:\ prompt)
>
> 5. Install XP Pro . When it asks for disk structure , first 'View existing
> partitions", just to be sure nothing there - no hardware error, then "
> Delete all "partitions. Then "Create" using all of the disk.
> That should do it.
>
> http://support.microsoft.com/kb/228888/en-us
> for the STOP error ( I know it says Windows 2000 , but just go with it)
> orhttp://support.microsoft.com/kb/935806
> ( halfway down)
> Search results for your
> problem:http://search.microsoft.com/Results....ll+XP+Stop+0x0...


I'm not doing all of that. I know what the stop error is for, but
clearly there's nothing wrong with my drive if I can install Windows
XP Home on it. However, I have noticed that installing a Service Pack
over it causes it to not boot. Is there a way to troubleshoot this
and then work from there?

 
Reply With Quote
 
- Bobb -
Guest
Posts: n/a
 
      11-19-2008, 09:04 PM
> > > JD Francis wrote:
> > > > I have an HP Compaq D310 Desktop, and recently purchased a Hitachi
> > > > Deskstar T7K250. When this hard drive is in the computer and I try
> > > > to
> > > > run the Windows XP Professional setup CD, it does not recognise any
> > > > of
> > > > the partitions and is unable to modify the disk in any way. When I
> > > > connect the drive to another computer via a USB cable and run the
> > > > setup, it can detect all the drive partitions and modify them.

>
> > > > Is there a way to get this hard drive working for Windows in my
> > > > computer?

>
> > > You purchased a used drive if it already had partitions on it. Wipe
> > > the
> > > hard drive clean with CopyWipe (free), and try again. The existing
> > > partitions are causing some confusion... Ben Myers

>
> > I already completely wiped it with the manufacturer's disk utility
> > program, but this made no difference to the Windows XP Professional
> > CD. I should probably add, that using a Windows XP Home CD, I am able
> > to install the operating system on the NTFS partition, which it
> > recognises, with no problems.

>
> > So it was a used drive?
> > Came from Windows environment ? ( vs. Unix,VMS, etc)
> > What do you mean by "completely wiped it" ?
> > Reformatted ?
> > If works as secondary drive, there the primary boot area is not used.
> > Did you look at disk structure when installing XP Home ?
> > Were there more than one partition ?
> > Were you able to delete existing partitions ?
> > Might it be you installed XP home to second partition?
> > So are you now all set, or still trying to install XP Pro
> > Can you install XP Pro NOW ( with XP home on there)

>
> The drive was used, yes. I don't know its history, but it did have a
> single NTFS partition on it when I got it that got deleted when I zero-
> filled the disk. Windows XP Home setup can see NTFS partitions and
> indicates that they are of this format, but the Windows XP
> Professional setup simply says "Unknown" and displays the error "Setup
> was unable to format the partition. The disk may be damaged" message
> when I try to manipulate the drive in any way.
>
> I've already tried installing XP Professional from a Home
> installation. Everything works fine up until the point where it
> reboots, where I get a Stop 0x00000024 error.
>
> The drive is fine; I've already run a scan on it. I believe the error
> is to do with either the configuration of the drive or that of the
> computer, rather than a fault with the drive. Also, on another thread
> I started in another group, somebody asked whether the XP Professional
> disk had a SP other than 1 on it while the XP Home disk had SP1 on
> it. This is correct, so I am wondering whether this difference in
> service packs bears any significance on the issue I am having.
> However, I have no way of obtaining an XP Professional SP1 disk so I
> am kinda screwed there if that is the cause of the problem.
> ========
> Stop 24 error:
> " an unrecoverable error when trying to access an NTFS partition or a
> volume
> on the hard disk. Typically, you receive a "Stop: 0x00000024" error
> message
> when the file system or partition structure is corrupted "
>
> I've installed XP Pro w/SP2 from scratch, and it installed fine so I don't
> think it's your software CD. Still sounds like physical disk issue to me.
> I
> suspect drive was previously in non-NTFS environment and the boot area is
> not recognized by install program. Why an issue in Pro and not Home ?
> Perhaps utilities dated differently ?? whatever the reason:
> Are you familiar with FDISK ?
> " The fdisk command in Windows 95 and Windows 98 lets you delete NTFS
> partitions by selecting and deleting the NON-DOS partition. "
>
> Can you make a Win98 boot disk ? or Norton Ghost ? Ultimate Boot CD etc
> to be able to :
> 1. boot a floppy ( or CD). Then, in DOS (either PC DOS or MS-DOS)
> 2. low level format the drive
> 3. partition the drive
> 4. format the drive ( FAT32)
> 5. run chkdsk /f just to check drive
> 6 if you are familiar with SYS command,
> type sys C:
> to initialize the boot block ( to boot up Win98 )
> (http://www.computerhope.com/syshlp.htm )
>
> Doing those steps will erase everything on the drive , then make sure that
> the boot block is writeable- and chkdsk should finish with no errors.
> Check
> the output for bad blocks etc.
> That should get you to a blank disk that has one and only one partition
> and
> a good boot block.
>
> Now that the drive has been initialized, boot the XP Pro CD ( make CD
> first
> in flow, otherwise will get Win98 C:\ prompt)
>
> 5. Install XP Pro . When it asks for disk structure , first 'View existing
> partitions", just to be sure nothing there - no hardware error, then "
> Delete all "partitions. Then "Create" using all of the disk.
> That should do it.
>
> http://support.microsoft.com/kb/228888/en-us
> for the STOP error ( I know it says Windows 2000 , but just go with it)
> orhttp://support.microsoft.com/kb/935806
> ( halfway down)
> Search results for your
> problem:http://search.microsoft.com/Results....ll+XP+Stop+0x0...

-------------------
> I'm not doing all of that. I know what the stop error is for, but clearly
> there's nothing wrong with my drive if I can > install Windows XP Home on
> it. However, I have noticed that installing a Service Pack over it causes
> it to not
> boot. Is there a way to troubleshoot this and then work from there?

=================
You mention XP Pro and XP Home - these are both FULL versions ? or Compaq
versions ? Assuming both store-bought ...

> The drive was used, yes. I don't know its history, but it did have a
> single NTFS partition on it when I got it that got deleted when I zero-
> filled the disk.


Using what app ?
Did you do that BECAUSE XP Pro failed or had you ever tried it ?

The fact that XP HOME installs and Pro does NOT, means the data surface of
the drive is fine, but NOT that the disk master boot record does not have
issues. CLEARLY there IS something wrong with your drive. What if security
is enabled on the drive? XP Home does not use EFS. XP Pro does. Who knows
how it was last initialized prior to you getting it. Maybe that's WHY you
got it !

Short of me runnings diags on it, I do not know for sure why it fails, but
you asked how to fix it. Without knowing the details of WHY it fails, we can
tell you HOW to fix it - no matter what the reason. Sorry if too many steps
my way. Otherwise, you'll have to live something OTHER than a secure OS.
( No XP Pro)

If you think not a Compaq issue, maybe try XP newsgroup ??


 
Reply With Quote
 
 
 
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Removable CD drive / floppy drive not recognised BertieBigBollox@gmail.com Laptops 4 09-08-2007 06:07 AM
Hard drive size not recognised by win98SE Steve Laptops 6 03-15-2006 03:58 AM
Compaq Presario R3000 New hard drive not recognised! Sherb Laptops 1 01-17-2006 10:41 PM
P4C800-E Deluxe & Multipule W2K OS partitions, problems installing to 2nd & 3rd partitions? Tim Asus 5 10-31-2005 06:41 AM
"OS no recognised" hard drive not being picked up harrylopes@hotmail.com Laptops 3 02-28-2005 01:31 AM


All times are GMT. The time now is 11:56 PM.


Welcome!
Welcome to Motherboard Point
 

Advertisment