1. This forum section is a read-only archive which contains old newsgroup posts. If you wish to post a query, please do so in one of our main forum sections (here). This way you will get a faster, better response from the members on Motherboard Point.

2,4@3,2 HELP: PCI 1 (1h) : PCI 32-bit 5V 3.3V PME HalfLength Available/AGP (7h) : AGP-4x 32-bit 3.3V

Discussion in 'Overclocking' started by N´far, Jan 17, 2004.

  1. N´far

    N´far Guest

    Pls help:
    20 to 30% performance increase here, but...

    Stabile at 2D, but drops to desktop after about 1 minute or 2 at 3D (PC
    mark2001 or CoD) .
    Since FBS 133 FBS ( before 100 ) I can´t see any PCI or AGP bus speeds
    anymore with prgs. I´m quite sure, could see PCI or AGP bus speeds before
    changing to 133...


    SiSoftware Sandra says:


    System Chassis
    Manufacturer : Chassis Manufacture
    Case Type : Tower
    Can be locked : No
    Version : Chassis Version
    Serial Number : Chassis Serial Number
    Asset Tag Number : Asset-1234567890
    Boot-up State : Safe
    Power State : Safe
    Thermal State : Safe

    System Mainboard
    Manufacturer : ASUSTeK Computer INC.
    MP Support : No
    Model : P4B266
    Version : REV 2.xx
    Serial Number : xxxxxxxxxxx
    BIOS ID : 08/06/2002--I845--P4B266

    System Memory Controller
    Location : Mainboard
    Error Correction Capability : None
    Number of Memory Slots : 3
    Maximum Installable Memory : 2GB
    Bank 1 - DIMM 1 : DIMM Synchronous DRAM 256MB/72
    Bank 2 - DIMM 2 : DIMM Synchronous DRAM 256MB/72
    Bank 3 - DIMM 3 : Empty

    System Chipset
    Model : ASUSTeK Computer Inc 82845/E/MP/MZ Brookdale CPU to I/O Bridge
    Bus(es) : AGP PCI IMB USB SMBus/i2c
    Front Side Bus Speed : 4x 133MHz (532MHz data rate)
    Max FSB Speed / Max Memory Speed : 4x 100MHz / 2x 133MHz
    In Order Queue Depth : 12 req(s)

    Chipset Hub Interface
    Type : HubInterface
    Version : 1.00
    No. Ports : 1
    Width : 8-bit
    Full Duplex : Yes
    Multiplier : 1x

    APIC 1
    Version : 2.00
    Multiplier : 1/2x
    Max Interrupts : 24
    IRQ Handler Engaged : Yes
    Enhanced Support : Yes

    Logical/Chipset Memory Banks
    Bank 0 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
    Bank 1 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
    Bank 2 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
    Bank 3 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL


    -------------->>>>>>> hmm.... got 2x 128 PC2100 installed.... :-(


    Speed : 2x 133MHz (266MHz data rate)
    Multiplier : 1x
    Refresh Rate : 15.60µs
    Power Down Mode : No
    Fixed Hole Present : No

    System Clock Generator
    Model : ICS 950209
    Software Programmable : No
    Read-Back Support : Yes

    Environment Monitor 1
    Model : Asus ASB100 SMB
    Version : 3.01
    Mainboard Specific Support : No

    Temperature Sensor(s)
    Board Temperature : 23.0°C / 73.4°F
    CPU Temperature : 32.0°C / 89.6°F
    Power / Aux Temperature : 127.0°C / 260.6°F

    Cooling Device(s)
    Auto Fan Speed Control : No
    CPU Fan Speed : 2265rpm

    Voltage Sensor(s)
    CPU Core Voltage : 1.71V
    Aux Voltage : 1.71V
    +3.3V Voltage : 3.33V
    +5V Voltage : 5.05V
    +12V Voltage : 11.25V
    -12V Voltage : -11.75V
    -5V Voltage : -4.93V

    AGP Bus
    Version : 2.00
    Current Data Transfer Rate : 4x
    Side Band Enabled : Yes
    Fast-Writes Enabled : Yes
    Aperture Size : 128MB

    PCI Bus(es)
    Version : 2.20
    No Bridges : 2
    PCI Bus 0 : 32-bit PCI (1x PCIClk)
    PCI Bus 2 : 32-bit PCI (1x PCIClk)

    LPC Hub Controller 1
    Model : Intel Corporation 82801BA (ICH2) LPC Interface Controller
    ACPI PM Enabled : Yes
    Random Number Generator Enabled : No
    Random Number Generator Support : Yes

    USB Controller 1
    Model : Intel Corporation 82801BA/BAM (ICH2) USB Universal Host Controller
    Version : 1.10
    UHCI Interface : Yes
    Channels : 2
    Speed : 48MHz
    Legacy Emulation Enabled : No

    USB Controller 2
    Model : Intel Corporation 82801BA/BAM (ICH2) USB Universal Host Controller
    Version : 1.10
    UHCI Interface : Yes
    Channels : 2
    Speed : 48MHz
    Legacy Emulation Enabled : No

    System SMBus Controller 1
    Model : Intel 801xx SMBus
    Version : 0.05
    Speed : 16kHz

    Expansion Slot(s)
    PCI 1 (1h) : PCI 32-bit 5V 3.3V PME HalfLength Available (Intel Corporation
    82845/E/MP/MZ Brookdale CPU to AGP Bridge)
    PCI 2 (2h) : PCI 32-bit 5V 3.3V PME HalfLength Available
    PCI 3 (3h) : PCI 32-bit 5V 3.3V PME HalfLength Available
    PCI 4 (4h) : PCI 32-bit 5V 3.3V PME HalfLength Available
    PCI 5 (5h) : PCI 32-bit 5V 3.3V PME HalfLength InUse
    PCI 6 (6h) : PCI 32-bit 5V 3.3V PME HalfLength Available
    AGP (7h) : AGP-4x 32-bit 3.3V PME HalfLength InUse

    Port Connector(s)
    PRIMARY IDE/HDD : None - ATA / None
    SECONDARY IDE/HDD : None - ATA / None
    FLOPPY : None - Floppy / None
    USB1 : USB - None / USB
    USB2 : USB - None / USB
    USB3 : USB - None / USB
    USB4 : USB - None / USB
    PS/2 Keyboard : Keyboard Port - None / PS/2
    PS/2 Mouse : Mouse Port - None / PS/2
    Parallel Port : Parallel Port ECP/EPP - None / DB25 pin female
    Serial Port 1 : Serial Port 16550 Compatible - None / DB-9 pin male
    Serial Port 2 : Serial Port 16550 Compatible - None / DB-9 pin male
    Joystick Port : Joystick Port - None / DB-15 pin female
    MIDI Port : MIDI Port - None / DB-15 pin female
    Line In Jack : Audio Port - None / Mini-jack
    Headphone : Audio Port - None / Mini-jack
    Microphone : Audio Port - None / Mini-jack
    Video Port : Video Port - None / Mini-jack
     
    N´far, Jan 17, 2004
    #1
    1. Advertisements

  2. N´far

    N´far Guest

    **************' -------------->>>>>>> hmm.... got 2x 128 PC2100
    installed.... :-(
    Found some nv4_ files. Will try to delete all af them and see what
    happens...
    tomorrow ;-)
    Using 53.03 drv

    Why can´t I see my AGP/PCI BUS SPEED anymore using fx. sandra, eida and
    some more...???
     
    N´far, Jan 17, 2004
    #2
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.