Slot T upgrade adapter and celeron Tualatin 1.1

[Bolooser11]

Good day,
I still have my BH6 1.02 (SS bios) running fine with a Celeron 850 and have been thinking of keeping it still some time and putting into it a slot T adapter (slot1 to socket 370) and a Celeron Tualatin 1.1. Is this a good idea or will it be a hassle especially with the voltage limitation of the BH6 ? Does anyone have this setup and does it work ok ? Thanks

 

[TomG]

be advised that some boards will not run well or possibly even boot with the slot-T adapter. I fitted a board with a Tualatin adapter and it would not boot about 90% of the time... bad enough that I went after a non-Tualatin cpu and wrote off the cost of the adapter and Tualatin cpu. your mileage may vary.

 

[Michael S Fedor]

I used the slot-T adapter on a Bx6 Rev2 with a 1.3Cel and everything works perfectly. "Bolooser11" wrote:

Good day,
I still have my BH6 1.02 (SS bios) running fine with a Celeron 850 and have been thinking of keeping it still some time and putting into it a slot T adapter (slot1 to socket 370) and a Celeron Tualatin 1.1. Is this a good idea or will it be a hassle especially with the voltage limitation of the BH6 ? Does anyone have this setup and does it work ok ? Thanks

 

[Spajky]

On Sat, 1 Nov 2003 23:26:50 +0100, "Bolooser11"
wrote:

I still have my BH6 1.02
it a slot T adapter (slot1 to socket 370) and a Celeron Tualatin 1.1. Is this a good idea Does anyone have this setup and does it work ok ?

should be working w/o problem

-- Regards, SPAJKY
& visit site - http://www.spajky.vze.com
Celly-III OC-ed,"Tualatin on BX-Slot1-MoBo!"
E-mail AntiSpam: remove ##

 

[BigVoice]

I am using slot-T on 1.4 Celly o/c to 1.52G without any problem with my BX6 Rev.2. BH6 should be OK I believe.

Bigvoice

On Sat, 1 Nov 2003 21:59:32 -0500, "Michael S Fedor"
wrote:

I used the slot-T adapter on a Bx6 Rev2 with a 1.3Cel and everything works perfectly. "Bolooser11" wrote:

Good day,
I still have my BH6 1.02 (SS bios) running fine with a Celeron 850
and have been thinking of keeping it still some time and putting into
it a slot T adapter (slot1 to socket 370) and a Celeron Tualatin 1.1.
Is this a good idea or will it be a hassle especially with the voltage
limitation of the BH6 ?
Does anyone have this setup and does it work ok ?
Thanks
...

 

[Bolooser11]

Thanks a lot for your answer man.
This is what I felt but not put into words;
The thing is that this BH6 runs so smooth and fine all the time that u always want to get more out of it, which u do until u push just a bit too far and get nothing anymore. Guess I'll go after a Celeron 1.1 Coppermine Thanks again

TomG a �crit dans le message :
9yWob.57257$N94.48021@lakeread02...

be advised that some boards will not run well or possibly even boot with the slot-T adapter. I fitted a board with a Tualatin adapter and it would not boot about 90% of the time... bad enough that I went after a non-Tualatin cpu and wrote off the cost of the adapter and Tualatin cpu. your mileage may vary.

--

Thomas Geery
Network+ certified

ftp://geerynet.d2g.com
ftp://68.98.180.8 Abit Mirror <----- Cable modem IP
...

 

[TomG]

good luck with it.

 

[tf]

I've got a Cel 1.1 + Cu slotket. If I was upgrading at this time from a 300a, which is what I did whenI went to the 1.1, 566, etc., I'd get a Tully 1.3 or 1.4 + a Slot-T.

"Spajky" <Spajky##@volja.net> wrote:

On Sat, 1 Nov 2003 23:26:50 +0100, "Bolooser11" wrote:

I still have my BH6 1.02
it a slot T adapter (slot1 to socket 370) and a Celeron Tualatin 1.1. Is this a good idea
Does anyone have this setup and does it work ok ?

should be working w/o problem

-- Regards, SPAJKY
& visit site - http://www.spajky.vze.com
...

 

[Homie]

I had similar results to Tom G but this was with the upgradeware 370/T adapter....Tried it on several boards and got different strange results every time.

On the other hand, I have not tried the slot T adapter and have heard only a few complaints.

My personal choice for the BH6 would be to find a 1 gig slot 1 OEM on E-bay

Homie